Float, toughened, laminated and insulating glass in practice
When two quotes for the same opening differ, it is rarely the price per square metre. It is usually the type of glass. This text explains the four types that an ordinary job chooses between, and above all what that choice means for you.

Float glass
Ordinary clear sheet glass. It is made by floating the molten mass on a bath of molten tin, hence the name. It is cheap, it can be cut, drilled and ground, and it is available almost immediately.
The drawback is how it behaves when broken: it breaks into long sharp shards. That is why it is used where impact is not expected, in furniture infills, shelves out of reach, picture glazing and small infills.
Toughened glass
Float glass that has been through a toughening furnace and rapid cooling. That gives it markedly higher resistance to impact and to temperature differences. Above all, when it does break it shatters into small blunt fragments that cause far less serious injury.
One thing about toughened glass is fundamental and worth repeating: once toughened, it can no longer be cut or drilled. Every dimension, hole and cut-out has to be specified before production. Any later change means a new pane.
It is used for shower screens, glass doors, shelves, splashbacks behind a kitchen worktop and glazing where load is expected.
Laminated glass
Two or more panes bonded with a flexible interlayer. When broken, the glass cracks but the fragments stay on the interlayer and the pane does not fall out. It is therefore used where the main risk is glass falling or a person falling through it: balustrades, overhead glazing, glazed walls by staircases.
Laminated glass has side effects that are often the reason for choosing it in the first place: it damps sound better and the interlayer blocks most ultraviolet light.
Insulating double and triple glazing
This is not a type of glass but an assembly. Two or three panes are joined around the perimeter by a spacer bar and the cavity between them is filled with dry air or gas. The unit is made and ordered as a whole, not pane by pane.
The individual panes inside a unit can be different. The outer one is often toughened or laminated, depending on where the window is.
The typical failure of an insulating unit is misting between the panes. It means the spacer has failed and moisture has got inside. It cannot be cleaned; it is solved by replacing the whole unit.
How the choice is made
A customer normally does not choose the type of glass. They choose a place and a purpose, and the type follows. Three questions help:
- Can anyone bump into the glass or lean on it?
- Is the glass overhead, or above somewhere it could fall onto?
- Does the glass have to separate something: heat, noise or moisture?
The first question leads to toughened or laminated glass, the second almost always to laminated, the third to an insulating unit.
No numbers here, and that is deliberate
Thicknesses, make-ups and standard numbers vary with the size of the pane, the way it is held, the load and the position. Copying them from a catalogue would mean asserting something that need not hold for your particular place. We therefore have the requirement for your job confirmed by the glazing firm that will run it.
What this means for your enquiry
Do not state a glass type unless you are sure. Describe the place: where the glass goes, what is around it, whether people walk past, whether it is a damp room, how large it is. The glass type is the answer, not the brief. The overview table of glass types is on the home page.
Frequently asked questions
Is toughened glass unbreakable?
It is not. It resists impact and temperature differences better than float glass, but it can be broken, typically by a blow to the edge. Its main benefit is how it behaves when broken, shattering into small blunt fragments.
What is the difference between laminated and toughened glass?
Toughened glass shatters into small fragments and falls out of the frame. Laminated glass cracks but holds together on the interlayer. That is why laminated glass is used where the glass must not fall out, for example in balustrades and overhead.
Can you tell the glass type by looking?
Not reliably. Toughened glass usually carries a mark fired into one corner, laminated glass shows the interlayer at the edge, and an insulating unit shows a spacer bar from the side. Only a survey gives certainty.
Send us the glass sizes
An e-mail address is enough. Tell us what broke or what you need made, and add the dimensions even if they are only approximate.
- Describe the place the glass is going, not the type of glass.
- Mention whether anyone can bump into it.
- A photo says more than a description.