Glass cut to size: float, toughened, heat-resistant and insulating
Glass cut to size is not ordered by type but by the place it is going into. The size, the shape, the edge finish and every hole have to be in the brief before the sheet is made, because once glass is toughened nothing can be trimmed or drilled any more.

Which glass is most often cut to size
- Float glass. Ordinary clear sheet glass. Shelves, furniture infills, picture glazing, cabinet doors. Cut from a sheet and usually available fastest.
- Toughened glass. Heat-strengthened. Used where load or impact is expected: shower screens, glass doors, shelves with a wider span, splashbacks behind a hob.
- Laminated glass. Two or more panes bonded with an interlayer. It holds together once broken, so it is used where the glass must not fall out.
- Heat-resistant glass. For stove and fireplace doors and places with high temperatures. Neither ordinary nor toughened glass does that job, and a replacement is ordered to suit the specific appliance.
- Insulating double or triple glazing. Made as a finished unit with a spacer bar. It is ordered as a whole, not pane by pane.
How to measure glass for a replacement
- Decide what you are measuring. The size of the opening (the clear distance between the beads) and the size of the pane are two different numbers. Say in the enquiry which one you are sending.
- Measure with the bead lifted, if you can. With the glazing bead off you can see how the glass actually sits. Without that, the measurement is indicative.
- Measure in millimetres. An estimate in centimetres is not enough for glass.
- Measure in several places. The width at the top, middle and bottom; the height on the left, in the middle and on the right. Old frames are rarely regular, and the smallest value is the one that matters.
- Check the diagonals. If they differ noticeably, the opening is not square and a template will be needed.
- Leave the allowance to the glazier. Glass is never fitted tight; the allowance for seating and thermal movement belongs in the production stage. Do not deduct it yourself, or it ends up being deducted twice.
- Measure the thickness too. With a caliper at the edge, or leave it to the survey. On a sealed unit the spacer width is visible from the side.
This is enough for a first estimate. To order the pane the size is always confirmed by a survey on site, because nobody guarantees a sheet that does not fit when it was made to your own measurement.
Edge finish
On glass cut to size the edge is a line item of its own, not a detail:
- Plain cut edge. For glass that will be fully hidden in a frame or a bead.
- Ground edge. The basic removal of the sharp arris so the glass is safe to touch.
- Polished edge. For visible edges of shelves, table tops and free-standing panes.
- Bevel. A chamfered, ground band around the perimeter. Typical on mirrors, where it also works visually.
Holes, cut-outs and shape
A simple rule applies: whatever is not in the brief before production normally cannot be added. For toughened glass that is absolute. Every hole for hardware, a handle, a socket or a light fitting, every cut-out for a pipe and every cut corner has to be drawn before the sheet goes into the toughening furnace. For non-standard shapes it is common for the firm to take a template on site from card or film.
What to put in the enquiry
- where the glass is going and whether anyone can bump into it or lean on it,
- the dimensions, and whether they are of the opening or of the pane,
- which edge will be visible,
- holes and cut-outs including their position,
- whether the glass should be clear, obscured or coloured,
- whether you need fitting too, or only making and collection.
If you do not know which type to choose, describe the place. The glass type is a result, not an input, and the table of glass types on the home page shows what the choice is between.
Frequently asked questions
Can toughened glass be trimmed or drilled?
No. Once heat-treated, toughened glass shatters if you try to cut or drill it. All dimensions, holes and cut-outs therefore have to be in the brief before toughening.
How long is the wait for glass cut to size?
Ordinary float glass is normally cut from a sheet in stock. Toughened and laminated glass and insulating units are ordered from the factory, so there is a wait. The lead time should be stated in the quote.
Do I need a survey if I have the old dimensions on an invoice?
Old dimensions are a good start, but frames move over time and the previous replacement may have been measured differently. For an order, the size is confirmed by a survey on site.
Send us the glass sizes
An e-mail address is enough. Tell us what broke or what you need made, and add the dimensions even if they are only approximate.
- Say where the glass is going, not only which type you want.
- List holes and cut-outs; on toughened glass they cannot be added later.
- Mention whether you want fitting as well.