Skip to content
775 654 443 CS
Home / Window glazing and broken glass replacement

Window glazing and broken glass replacement

Replacing glass in a window means lifting the glazing bead or the old putty, removing the remains of the pane, measuring the opening and fitting a new sheet. The frame, the hardware and the sill normally stay in place, which makes it a cheaper and faster job than replacing the whole window.

A tradesman working on a white window frame during a glass replacement

When the glass alone is enough and when it is not

If only the glass is damaged and the frame still holds its shape, this is a glazing job. The window does not have to be removed, the pane is changed in place. Replacing the whole window makes sense when the frame is rotten or twisted, the hardware cannot be adjusted or the window will not close.

Misted double glazing is a special case. The mist between the panes is not dirt that can be washed off. It is moisture that got inside the unit past a failed spacer bar. It is solved by replacing the whole insulating unit; the frame stays.

Timber, uPVC and aluminium frames

Each type of frame is glazed differently, and that shapes the work:

  • Timber frame. Older windows tend to be bedded in putty and held by glazing sprigs, newer ones by a bead. Removing old putty is the most laborious part, and it is usually where the condition of the timber underneath becomes apparent.
  • uPVC frame. The glass is held by a glazing bead that is prised off around the perimeter. Underneath there are packers that set how the unit sits in the frame. Fitted wrongly, the window becomes stiff to close.
  • Aluminium frame. Handled much like uPVC, but the profiles are narrower and the formats are more often large, so more people or lifting equipment may be needed.

What to send with your enquiry

The more of this list you send straight away, the more concrete the answer will be:

  • a photo of the whole window and a close-up of the frame where the glass sits,
  • approximate pane dimensions, or at least the dimensions of the sash,
  • whether it is single glazing or a sealed unit (seen from the side, a unit shows two panes and a spacer between them),
  • the frame material and roughly how old the window is,
  • the floor, and whether the window can be reached from inside or the work has to be done from outside,
  • whether the opening is temporarily boarded up at the moment.

Before the glazier arrives

Do not pull shards out of the frame with bare hands and do not leave them lying around, especially with children or pets in the house. A firm board or strong sheeting taped around the perimeter usually works to cover the opening. If the pane has only cracked and still holds in the frame, tape on both faces reduces the risk of it collapsing when the sash is opened.

Safety glass in windows

In some positions laminated or toughened glass is used instead of ordinary glass. Typically this means large glazed areas, door infills, windows by a staircase and places where impact or a fall is possible. What exactly is required in your case normally follows from the standards and from the building design. We do not guess it from a photo; we have it confirmed by the firm that will run the job.

Shopfronts, glazed walls and large formats

For shopfronts and large panes, handling is added to the cost of the glass. A large-format sheet is not carried by hand; it needs suction cups, sometimes equipment and more people. There is more about this on the page about shopfronts, door glazing and glass splashbacks.

Frequently asked questions

Can glass be replaced without taking the whole sash out?

In most cases yes. The glass is changed in the frame itself; the sash is only secured or, depending on access, lifted off its hinges. Taking the whole window out is needed mainly for large formats and for glazing that cannot be reached from inside.

What does it mean when double glazing mists up inside?

It means the spacer bar between the panes has failed and moisture has got inside the unit. It cannot be cleaned. The fix is to replace the whole insulating unit; the frame and hardware stay.

Does someone have to be at home for the survey?

Yes, the survey needs access to the window from inside. It normally takes a short while, and the fitting date is often agreed on the spot.

Send us the glass sizes

An e-mail address is enough. Tell us what broke or what you need made, and add the dimensions even if they are only approximate.

  • Give the sash and pane dimensions if you have them.
  • Attach a photo of the window; it speeds things up a lot.
  • Mention the floor and how the window can be reached.

Only the e-mail is required. Fill in the phone number if you would like us to call.