Skip to content
775 654 443 CS
Home / Blog / Custom mirror: bevel, backing and fixing

16 November 2026

Custom mirror: bevel, backing and fixing

Of all glazing jobs a mirror is the one seen most, and the one where preparation is most often underestimated. There are three decisions that have to be made before production: the edge, the fixing and the cut-outs.

A large made-to-measure mirror above a vanity unit

Edge: ground or bevelled

A mirror is normally not set into a frame, so the edge stays visible. That makes it part of the look, not a technical detail.

  • Ground and polished edge. A straight, smooth side. An understated choice that suits modern interiors and wall mounting.
  • Bevel. A chamfered, ground band around the perimeter. In daylight it reads as a thin line that frames the mirror. Chosen where the mirror should read as an object rather than a surface.

Both are done in production. The edge is not reworked afterwards.

Backing and protecting the rear face

The back of a mirror is delicate. It is a metal coating protected by lacquer, and both moisture and the wrong adhesive will damage it. That is where the dark patches creeping in from the edge of old mirrors come from.

Two things follow:

  • The adhesive has to be made for mirrors. Ordinary construction adhesive or silicone can attack the backing, and it shows up only months later.
  • Safety film on the rear face is an optional treatment. It holds the fragments together if the mirror breaks. It is worth it on large panes, in hallways and wherever children are about.

Fixing

The fixing decision has to be made before production, because it determines whether holes will be drilled.

  • Bonding to the wall. The cleanest look, with the mirror flush to the wall. It needs a flat, dry and sound substrate. It is not the answer for a freshly built partition or a wall that will be altered later.
  • Mirror clips or a hanging system. Removable. Suits rented places and walls that are less than ideal.
  • Through-fixing via holes. The holes are drilled in production. Drilling a finished mirror is not done.

Light fittings and switches

The most common complication with a bathroom mirror is not the glass but the wiring. The supply is usually somewhere other than where the mirror would logically go, and then it is either a cut-out, a shifted mirror or new cabling. Settling that before the survey saves an extra round.

If you want backlighting, say which kind: a fitting above the mirror, a strip behind it, or a sandblasted band in the mirror coating for light to pass through. Each variant needs different preparation.

Where mirrors cause trouble

  • an edge exposed to running water, typically right above a basin with no gap,
  • an uneven wall that breaks up the reflection,
  • fresh plaster or a new partition that is still drying,
  • a position above a permanently warm surface,
  • a wall that will later be drilled for something else.

What to settle before the enquiry

  1. the dimensions, and whether it is free wall or an exact gap between furniture,
  2. whether it is for a bathroom,
  3. the edge: ground or bevelled,
  4. cut-outs for a light fitting, a switch or a handle,
  5. how the mirror should be held,
  6. whether you want fitting as well.

There is more on the individual options on the page about mirrors made to size.

Frequently asked questions

Why do old mirrors get dark patches at the edges?

That is damaged backing. Either moisture reached it or the wrong adhesive attacked it. It cannot be repaired; the mirror is replaced.

Can a mirror be hung on plasterboard?

It can, but depending on the weight of the pane the fixing has to go into a stud or use special anchors. Bonding onto plasterboard is only done where the board is well fixed and flat.

Send us the glass sizes

An e-mail address is enough. Tell us what broke or what you need made, and add the dimensions even if they are only approximate.

  • Give the dimensions and where the mirror is going.
  • Decide the edge: ground or bevelled.
  • Mention a light fitting or a switch in that spot.

Only the e-mail is required. Fill in the phone number if you would like us to call.